Skip to content
RoofReady

Roof replacement cost

What does a new roof cost? Here's what actually sets the price.

Most roof replacements are priced per square. Start with the typical range, run the math for your own roof, then see what moves the number up or down.

What a new roof costs per square

Typical price per square

$500–$1,000

per roofing square (100 sq ft)

Additional decking sheets:
$50–$100 per sheet beyond the 2–4 typically included

Roofers price a replacement by the square: 100 square feet of roof surface. Count the squares on your roof, multiply by a price per square, and you have the core of an estimate.

Decking is the common add-on. If rotted sheets turn up during tear-off beyond what's included, each extra sheet is priced separately.

The math on a typical home

Take a home with about 2,000 square feet of roof area: the surface of the roof itself, not the living space inside. That's 20 squares.

20 squares × $500–$1,000 = $10,000–$20,000

A number of factors affect where a specific roof falls in that range, including pitch, complexity, material, layers and decking. See how each one works.

That's a starting point, not a quote. Only a roofer who measures and inspects your roof can tell you where yours lands.

Figures are general ranges from a local roofing professional, not a quote. Your price depends on your roof and is set only by the roofing professional who inspects it.

Why footprint matters more than house size

Roof area isn't the same as living space, the square footage you'd see on a listing. A one-story home usually has more roof than a two-story with the same living space, because all of its rooms sit under the roof instead of being stacked. A ranch with 2,000 sq ft of living space can need noticeably more squares than a two-story with 2,000 sq ft of living space.

Overhangs and pitch add area too: the steeper the roof, the more surface it takes to cover the same footprint. That's why roofers measure the roof itself, not the house, and why the example above starts from roof area.

What a thorough roof evaluation includes

Whoever you hire, a good roofer looks at your roof before putting a number on it. Expect them to:

  • Check the attic for ventilation, moisture, and the condition of the decking from underneath.
  • Get up on the roof, or inspect it closely by drone, to see shingles, flashing, vents and soft spots for themselves.
  • Measure from that inspection, not a satellite report alone. Satellite measurements can be a useful starting point for roof area, but they can't show soft decking, worn flashing, or how many layers are already on the roof.

If a quote shows up without anyone looking at your roof, ask how it was put together. More on what a roof evaluation covers.

The factors that drive roof replacement cost

Roughly in the order they tend to matter.

  1. Roof size

    The biggest single driver. More squares means more material, more labor, and more debris.

    Material, labor and disposal all scale with area, so size sets the baseline that everything else adjusts. This is also why a quote for a two-story house can be smaller than one for a sprawling one-story ranch: the ranch may simply have more roof.

  2. Roof shape and complexity

    Every valley, hip, dormer, and change in direction adds labor and waste.

    A simple two-sided gable roof is the most efficient to replace. Valleys need extra underlayment and careful cutting; dormers and intersecting rooflines add flashing and slow the crew down. Skylights, chimneys and multiple pipe penetrations each need their own detail work.

    Complexity is why two roofs with the same number of squares can price differently.

  3. Pitch (steepness)

    Steeper roofs take more time and more safety equipment, and they're priced accordingly.

    Pitch is described as rise over run: a 6/12 roof rises 6 inches for every 12 inches across. Low and moderate pitches can be walked comfortably. Steeper roofs require roof jacks, harnesses and slower, more careful work, and many roofers add a per-square charge above a certain pitch.

    Very low-slope sections, like porch roofs, may need a different material altogether, since shingles need enough slope to shed water.

  4. Stories and roof height

    A second or third story means more ladder work, more fall protection, and harder debris removal.

    Taller homes take longer to load material onto and clear debris from, and they require more safety setup. On a walk-out basement home, one side of the roof may be much higher than it looks from the street.

  5. Roofing material

    The product you choose sets the price per square more than anything else you control.

    Architectural asphalt shingles are the most common replacement choice and the usual baseline. Premium or designer shingles cost more for heavier weight and more dimensional looks. Metal roofing, especially standing seam, costs more up front and is installed by more specialized crews. See asphalt shingle roofing and metal roofing for the trade-offs.

    Within a material, product line matters: matching starter strips, ridge cap and underlayment from the same manufacturer can be required for the strongest warranty.

  6. Tear-off and number of layers

    Removing the old roof is real labor. Each extra layer underneath adds to it.

    A standard replacement removes one layer of old shingles. Some homes have two layers because a previous roof was installed over the old one. Every additional layer means more labor, more weight to haul, and more disposal, and most roofers price it as an add-on.

    Tear-off also exposes the deck, which is the only way to find and fix damage underneath.

  7. Decking condition

    The one cost that can't be fully known until the old roof is off.

    Decking is the plywood or OSB the roof is nailed to. Sheets that are soft, rotted, or delaminated have to be replaced before the new roof goes on. Because nobody can see the whole deck in advance, most estimates list a price per sheet and confirm the count during tear-off.

    A good estimate tells you that unit price in writing. Some roofers include a set number of sheets in the base price. Ask which, so a decking allowance doesn't become a surprise.

  8. Flashing

    Metal detailing at walls, chimneys, valleys and vents: where most leaks start.

    New drip edge, pipe boots and step flashing are standard on most replacements. Chimneys are the big variable: a chimney may need new step and counter-flashing, or a cricket (a small peaked section) behind a wide chimney to stop water from pooling.

    Skylights may be re-flashed or replaced during the roof job. If a skylight is near the end of its life, doing it now usually costs less than doing it later.

  9. Ventilation

    A roof that can't breathe ages faster. Fixing ventilation is often part of the job.

    Attic ventilation lets heat and moisture escape. Poor ventilation can shorten shingle life, contribute to deck rot, and can affect manufacturer warranty coverage. A replacement is the easiest time to correct it, often by adding a ridge vent and making sure soffit intake isn't blocked.

    Expect a roofer to look in the attic. If they recommend ventilation changes, ask what they're seeing and what problem it solves.

  10. Underlayment and leak barriers

    The layer under the shingles. Quality varies, and so does price.

    Synthetic underlayment has largely replaced traditional felt on many roofs; it's lighter, stronger and less likely to tear. Self-adhered membranes are often used in valleys, around chimneys, and at other vulnerable spots. Some estimates use them more extensively than others, which is one reason similar-looking quotes differ.

  11. Labor

    Often the largest part of the bill, and the part that most affects how the roof performs.

    Installation quality determines whether a good material performs well. Labor cost reflects crew experience, local wages, and how long the roof will take given everything above. An unusually low price sometimes means less time spent on the details that prevent leaks.

    Ask who will actually be on the roof (the roofing company's own crew or a subcontractor) and who supervises the work.

  12. Access to the roof

    How easily the crew can get material up and debris down.

    A driveway close to the house where a dumpster or trailer can sit makes a job faster. Long carries, steep yards, landscaping, fences, pools, or overhead lines slow things down and can require extra protection or equipment.

  13. Debris removal and disposal

    Old roofing is heavy, and hauling and dumping it costs money.

    Disposal is usually built into the base price, but it grows with every extra layer and every square. Make sure the estimate includes dumpster or trailer fees, landfill charges, and cleanup, including a magnetic sweep for nails.

  14. Upgrades and add-ons

    Optional choices that raise the price but may be worth it for your home.

    Common options include premium shingle lines, upgraded underlayment, more extensive leak-barrier coverage, new gutters, skylight replacement, and enhanced manufacturer warranties that require specific system components and a qualified installer.

    None of these are required for a sound roof. A good roofer explains what each one does so you can decide what's worth it.

Material choices at a glance

Relative cost only. Your estimate sets the real numbers.

Comparison of common roof replacement materials
MaterialRelative costWhat it looks likeWorth knowing
Architectural asphalt shinglesBaselineLayered, dimensional shingleThe most common replacement choice; wide range of colors.
Premium / designer shinglesHigherHeavier, more textured; some mimic slate or shakeMostly about appearance; check the specific product's warranty.
Exposed-fastener metalVariesRibbed panels with visible screwsScrew washers need periodic attention over the life of the roof.
Standing seam metalHighest of theseClean vertical seams, hidden fastenersHigher up-front cost; long service life when well installed.

Costs that can show up after work starts

A good estimate anticipates these. If yours doesn't mention them, ask before you sign.

  • Decking replacement beyond what was included, priced per sheet.
  • An extra layer of old roofing discovered during tear-off.
  • Rotted fascia or soffit boards found when gutters or drip edge come off.
  • Chimney or skylight issues that weren't visible from the ground.
  • Permit fees, if a permit is required and not already included.

Change orders are normal on roofs. What matters is that unit prices are agreed in writing ahead of time, and that you're shown the problem before it's fixed.

Comparing prices without comparing apples to oranges

  • Confirm the number of squares in each estimate. A big gap means someone measured differently.
  • Check that the same material, by product line, is quoted.
  • Compare decking allowances and per-sheet prices, not just the total.
  • Look for flashing, ventilation and underlayment detail, not just "included."
  • Weigh the workmanship warranty. Who stands behind the installation, and for how long?

More on reading a quote line by line: How much does a new roof cost in North Georgia?

Paying for a new roof

Many homeowners pay over time. Some roofing companies offer financing through outside lenders, and there are other routes too: home equity, personal loans, or savings. Our roof financing guide explains how these usually work and what to ask about rates, fees, and promotional terms.

Roof cost questions

How much does a new roof cost in Ball Ground?

It comes down to how many squares your roof measures and the factors on this page: pitch, complexity, material, and what's under the old shingles. For a real number, an independent local roofing professional can measure your roof and give you a written estimate. Request one here.

Why do roof estimates vary so much?

Differences in measurement, material line, how much underlayment and flashing work is included, how decking is handled, and the labor and warranty behind the job. Line up the scope before comparing totals.

Is the cheapest estimate a bad sign?

Not automatically, but check what it leaves out. Low estimates sometimes skip new flashing, use minimal underlayment, or have a vague decking allowance that grows later.

Does RoofReady set the price?

No. RoofReady doesn't provide estimates or perform work. The price comes from the independent roofing professional who inspects your roof.

Get a number for your roof, not an average

Tell us about your home. An independent local roofing professional will measure the roof and give you an estimate. No obligation.

CallGet My Roof Estimate